Generating people presents can often be tough but is constantly the finest way, as it shows you actually care. By putting a lot of time, hard work and creativity into make some thing special just for them. Why not make that specific somebody a memory bracelet. You can spot photos in every of the tiles, they can be of items you have done with the individual, things they like, areas they have been or a themed thought this kind of as botanical.
The resources you will need to have to carry out this creation are as follows:
Polymer art clay or Fimo - white or other light colour, Pasta machine, Dark T-Shirt transfer paper, Photos at thumbnail sizes - print multiple photos, in situation one gets ruined, Eye pins, one for every single tile, - inch double-sided tape, Pewter metal sheet, Wooden stylus, Liquid polymer gel, Embossing warmth gun, Epoxy glue, Gloss varnish, Pre-produced bracelet chain, Jump rings, one particular for every tile, Silver charms of alternative.
1. To commence with, spot your polymer clay (or Fimo) in the pasta machine on the thickest setting. Then to create double thickness fold above the clay.
2. Print out the thumbnail sized pictures and employing your jewellery tools lower them down without a border. Meticulously peel of the back of the picture and apply to the clay. Rub over gently to remove any bubbles there may be and trim the clay down to the size of the picture. Reduce down the eye pin to inch, press into the top centre of every single tile. Then bake the tiles and eliminate the eye pins.
3. Following permitting cooling time from baking, apply double-sided tape close to the edges of the tile and lower a strip of pewter to inch. Remove the back of the tape and wrap the pewter all around the edges, start at the hole at the top and leave only a slight bit of the pewter sticking over the front. Employing the wooden stylus tool, push down the edges down more than the tile on the two sides.
4. Apply double-sided tape to the back of the, remove backing and place the piece onto the pewter. Cut to flush and utilizing the wooden stylus to soften the edges.
5. Add a semi-thick layer of liquid polymer to give a clean, glass-like look. Heat the gel with a heat gun to set it. While using the gun, never get to near to the piece, rotate so the entire piece gets dried.
6. Apply gloss varnish to all the pieces and substitute the eye pins and glue them in spot and attach them with jump rings.
7. If you want to have an extra appeal to the bracelet then you can add themed charm beads.
You can use as numerous or as small images and charm beads as you want. The pictures never have to be in colour, experiment with making use of adverse and sepia effects to add a vintage truly feel to the piece.
This will be a amazing present for a person near. They will never ever want to take this unique, unique piece off and they'll even feel it was store bought, and the greatest issue is you made it by yourself.
The resources you will need to have to carry out this creation are as follows:
Polymer art clay or Fimo - white or other light colour, Pasta machine, Dark T-Shirt transfer paper, Photos at thumbnail sizes - print multiple photos, in situation one gets ruined, Eye pins, one for every single tile, - inch double-sided tape, Pewter metal sheet, Wooden stylus, Liquid polymer gel, Embossing warmth gun, Epoxy glue, Gloss varnish, Pre-produced bracelet chain, Jump rings, one particular for every tile, Silver charms of alternative.
1. To commence with, spot your polymer clay (or Fimo) in the pasta machine on the thickest setting. Then to create double thickness fold above the clay.
2. Print out the thumbnail sized pictures and employing your jewellery tools lower them down without a border. Meticulously peel of the back of the picture and apply to the clay. Rub over gently to remove any bubbles there may be and trim the clay down to the size of the picture. Reduce down the eye pin to inch, press into the top centre of every single tile. Then bake the tiles and eliminate the eye pins.
3. Following permitting cooling time from baking, apply double-sided tape close to the edges of the tile and lower a strip of pewter to inch. Remove the back of the tape and wrap the pewter all around the edges, start at the hole at the top and leave only a slight bit of the pewter sticking over the front. Employing the wooden stylus tool, push down the edges down more than the tile on the two sides.
4. Apply double-sided tape to the back of the, remove backing and place the piece onto the pewter. Cut to flush and utilizing the wooden stylus to soften the edges.
5. Add a semi-thick layer of liquid polymer to give a clean, glass-like look. Heat the gel with a heat gun to set it. While using the gun, never get to near to the piece, rotate so the entire piece gets dried.
6. Apply gloss varnish to all the pieces and substitute the eye pins and glue them in spot and attach them with jump rings.
7. If you want to have an extra appeal to the bracelet then you can add themed charm beads.
You can use as numerous or as small images and charm beads as you want. The pictures never have to be in colour, experiment with making use of adverse and sepia effects to add a vintage truly feel to the piece.
This will be a amazing present for a person near. They will never ever want to take this unique, unique piece off and they'll even feel it was store bought, and the greatest issue is you made it by yourself.
About the Author:
Looking to find the best deal on pandora bracelets, then visit www.cheappandoracharms.org.uk to find the best advice on bracelets for you.
No comments:
Post a Comment